Your selection
DA-P
1.3 mm · black · unbacked
Width and length to roof measurements
Item number: 01002
COVERiT NovoProof®
DA-P
EPDM sheet
Fewer seams to weld on site.
Bad weather? No problem! An invaluable advantage of the COVERiT NovoProof® DA-P sheet is its great freedom of installation! Almost regardless of weather or temperatures, the sheet can be laid out at nearly any time. This is because the COVERiT NovoProof® DA-P sheet is extremely flexible from −40 °C to +120 °C, and ThermoFast® joining technology enables reliable welding of the sheet seams even at low outside temperatures.
Applications
Roof waterproofing
Green roofs
Under wearing layers
Special roof shapes
All types of substructure
New construction and refurbishment
Balconies and terraces
Structural waterproofing
Structural waterproofing and parking decks
External waterproofing of tunnels, bridges and underpasses
Waterproofing of building elements in contact with the ground (DIN 18533)
Waterproofing of indoor areas (DIN 18534)
EN 13501-5 BROOF(t1) under fully covering ballast to DIN 4102-4
DA-P: From plan to roof
Laying methods
Installation steps
- Lay in one piece As a large-area waterproofing layer, the COVERiT NovoProof® DA-P sheet is laid loose in one piece.
- Close seams and connections Position the sheet and close the remaining seams and connections. Arrange support for the first installation if needed.
- Secure with ballast With ballast, the roof covering is secured against wind uplift immediately after laying.
Carry out trial welds first and inspect the finished area. Hot-gas weld ThermoFast® seams, weldable under site conditions down to approx. −10 °C. Also for green roofs with photovoltaic systems.
The DA / DA-P product data sheet, July 2025, describes the material as flexible from −40 °C to +120 °C. This material property does not specify permissible installation temperatures. Joining remains subject to the installation instructions and required trial welds.
Choose your DA-P version
View in shop
The current data sheet does not state technical values for 1.2 mm. Confirm this version before ordering. Prices and ordering eligibility are shown in the shop.
Planning documents
COVERiT NovoProof® DA-P sheets are certified to DIN EN 13956 and DIN EN 13967. Declarations of performance for NovoProof DA to EN 13956, dated July 2025, and to EN 13967, dated May 2026. Product data sheet dated July 2025 (DE). Reaction-to-fire class E to EN 13501-1. Details and supporting documents depend on the roof build-up. FLL test report 24/20: The tested NovoProof DA/DA-P 1.3 mm variant is root-resistant and rhizome-resistant, without added biocides. The evidence is bound to the specimen and jointing method; it does not grant general approval for multilayer build-ups or bamboo. According to the manufacturer's product data sheet, 07/2025: resistant to ozone and UV, and to fungi and algae, microorganisms and humic acid.
12 / 12
Full-text search is temporarily unavailable. This list is searched by titles and summary details only; the filters still work.
Unknown filters were not applied.
- Product data sheet
DA / DA-P
07/2025
Earlier editions (1)
DA / DA-P
09/2020
- Product information
DA-P / DA-F
06/2023
- DoP roofing
DA - 1.3 mm
07/2025
Earlier editions (1)
DA - 1.3 mm
09/2020
- DoP roofing
DA - 1.5 mm
07/2025
Earlier editions (1)
DA - 1.5 mm
09/2020
- DoP roofing
DA - 2.0 mm
07/2025
- Installation guide
COV-SG
01/2020
- Tender specification
DA-P - Sheet
18.02.2025
- Test report
DA/DA-P - 1.3 mm
Test report dated 17 November 2020, valid until 17 November 2030
- Environmental product declaration
NovoProof EPDM
3 June 2025; valid until 2 June 2030
- DoP structural waterproofing
DA - 1.3 mm
05/2026
Earlier editions (1)
DA - 1.3 mm
09/2020
- DoP structural waterproofing
DA - 1.5 mm
05/2026
Earlier editions (1)
DA - 1.5 mm
09/2020
- DoP structural waterproofing
DA - 2.0 mm
05/2026
Earlier editions (1)
DA - 2.0 mm
09/2020
Compatible system products
Select preformed parts, penetrations and drainage to suit the connection design. Use EPDM versions. For seams and connections as per the data sheet: NovoProof® connection paste, cover tape, rubber support strip and composite metal sheets.
Pack sizes, order units and minimum quantities are listed in the shop.
Contact adhesive TA
For bonding upstands and connection details.
Preformed parts
Corners and sleeves for parapets, chimneys and rooflights. Prefabricated, including made-to-measure parts.
Roof drainage
Drain rainwater from the roof. Select an EPDM flange and outlet to suit the roof build-up and drainage design.
Roof penetrations
Route vents and cables through the roof. With a weldable NovoProof® EPDM sleeve.
Product images partly edited with AI assistance
Compare roll membranes
Backing and installation method determine which membrane suits the roof build-up.
Flame-retardant describes the material. Fire performance evidence applies to the tested roof build-up.
Also as sheetDA
Loose-laid under ballast. Unbacked. For gravel, green roofs and trafficable layers.
Thickness1.2 mm1.3 mm1.5 mm2.0 mm
Also as sheetDA-F
For exposed roofs. Flame-retardant. Without ballast in a tested roof assembly. Unbacked.
Thickness1.3 mm1.5 mm
DA-SK
Adhesive already on the membrane. Fully bond to a prepared substrate; use primer where required.
Thickness1.5 mm
DA-FG
Directly on unfaced EPS. No additional fire-protection layer in the specifically tested assembly.
Thickness1.3 mm1.5 mm
DA-S
Thick fleece for rough substrates. Existing roof layers may remain after assessment.
Waterproofing layer1.3 mm1.5 mm
Overall thickness2.5 mm2.7 mm
DA-K
Fleece backing for bonded roofs. Also suitable for mechanical fixing or laying under ballast.
Thickness1.3 mm1.5 mm
Product images partly edited with AI assistance
Compare sheets
Large-area sheets reduce on-site seam welding and detailing.
Current product
DA-P
Sheet for gravel or green roofs. Laid loose in one piece.
Thickness1.2 mm1.3 mm1.5 mm2.0 mm
DA-F Sheet
Made-to-measure, also without ballast. Induction-fixed in a tested roof assembly.
Thickness1.3 mm1.5 mm
Product images partly edited with AI assistance