Your selection
DA-FG · 200 m
1.3 mm · 1.30 m wide
Item number: 02012
COVERiT NovoProof®
DA-FG
Glass-fabric-backed EPDM roll membrane
Directly on EPS. In a tested roof assembly.
NovoProof® DA-FG is the glass-fabric-backed EPDM membrane for flat roofs subject to high loads. Its dimensionally stable construction makes efficient installation easier in new builds and refurbishment. Depending on the tested system build-up, the membrane is mechanically fixed or bonded.
Applications
Roof waterproofing
Without ballast
Green roofs
Under wearing layers
Special roof shapes
Parapets, upstands and roof penetrations
All types of substructure
New construction and refurbishment
Directly on unfaced EPS insulation
Directly on faced rigid polyurethane insulation, type PUR/PIR DAA dh
Mineral wool or mineral fibre insulation
Balconies and terraces
Structural waterproofing
Structural waterproofing and parking decks
External waterproofing of tunnels, bridges and underpasses
Waterproofing of building elements in contact with the ground (DIN 18533)
Waterproofing of indoor areas (DIN 18534)
EN 13501-5 Broof (t1) for tested constructions
Installing DA-FG
Laying methods
Installation steps
- Check the assembly Match insulation and fixing to the tested roof assembly.
- Secure the membrane Bond, mechanically fix or lay under ballast as specified. Position fixings to the wind-load calculation.
- Fix the edges Mechanically fixed: also fix roof edges, valleys, upstands and roof penetrations linearly with suitable, approved fixings, 4 per metre (see the installation guide).
- Close the seams Hot-air weld ThermoFast® overlaps and complete connections.
BROOF(t1) and BROOF(t3) are not interchangeable; use the classification for the roof assembly. Hot-air weld ThermoFast® seams, weldable under site conditions down to approx. −10 °C; carry out trial welds first. Rolls come with a ThermoFast® joining edge along the long side.
Choose your DA-FG version
View in shop
Prices and ordering eligibility are shown in the shop.
Planning documents
Declarations of performance: DA-FG to EN 13956, dated July 2025. Product data sheet dated July 2025 (DE). Reaction-to-fire class E to EN 13501-1. Details and supporting documents depend on the roof build-up. According to the manufacturer's product data sheet, 07/2025: resistant to ozone and UV, and to fungi and algae, microorganisms and humic acid.
11 / 11
Full-text search is temporarily unavailable. This list is searched by titles and summary details only; the filters still work.
Unknown filters were not applied.
- Product data sheet
DA-FG
07/2025
Earlier editions (1)
DA-FG
09/2020
- Product information
DA-FG
06/2023
- DoP roofing
DA-FG - 1.3 mm
07/2025
Earlier editions (1)
DA-FG - 1.3 mm
09/2020
- DoP roofing
DA-FG - 1.5 mm
07/2025
Earlier editions (1)
DA-FG - 1.5 mm
09/2020
- Installation guide
COV-SG
01/2020
- Tender specification
DA-FG - Waterproofing Membrane
18.02.2025
- Environmental product declaration
NovoProof EPDM
3 June 2025; valid until 2 June 2030
- DoP structural waterproofing
DA-FG - 1.3 mm
05/2026
Earlier editions (1)
DA-FG - 1.3 mm
09/2020
- Test certificate
- Germany
NovoProof DA-S / DA-K / DA-FG - P-3230-1245-MPA BS
Valid 2021–2026
Applies to NovoProof DA-S, DA-K and DA-FG.
PDF to follow
- Test certificate
- Germany
NovoProof DA-FG - P-2300-832-16-MPA BS
Valid 2021–2026
Applies to NovoProof DA-FG.
PDF to follow
- DoP structural waterproofing
DA-FG - 1.5 mm
05/2026
Earlier editions (1)
DA-FG - 1.5 mm
09/2020
Compatible system products
Select preformed parts, penetrations and drainage to suit the connection design. Use EPDM versions. For seams and connections as per the data sheet: NovoProof® connection paste, cover tape, rubber support strip and composite metal sheets.
Pack sizes, order units and minimum quantities are listed in the shop.
Contact adhesive TA
For bonding upstands and connection details.
Seam fastening
Plates and fasteners for mechanical fixing at membrane seams.
Preformed parts
Corners and sleeves for parapets, chimneys and rooflights. Prefabricated, including made-to-measure parts.
Roof drainage
Drain rainwater from the roof. Select an EPDM flange and outlet to suit the roof build-up and drainage design.
Roof penetrations
Route vents and cables through the roof. With a weldable NovoProof® EPDM sleeve.
NovoWeld
Induction fastening without penetrating the waterproofing. For approved roof build-ups only.
Product images partly edited with AI assistance
Compare roll membranes
Backing and installation method determine which membrane suits the roof build-up.
Flame-retardant describes the material. Fire performance evidence applies to the tested roof build-up.
Also as sheetDA
Loose-laid under ballast. Unbacked. For gravel, green roofs and trafficable layers.
Thickness1.2 mm1.3 mm1.5 mm2.0 mm
Also as sheetDA-F
For exposed roofs. Flame-retardant. Without ballast in a tested roof assembly. Unbacked.
Thickness1.3 mm1.5 mm
DA-SK
Adhesive already on the membrane. Fully bond to a prepared substrate; use primer where required.
Thickness1.5 mm
Current product
DA-FG
Directly on unfaced EPS. No additional fire-protection layer in the specifically tested assembly.
Thickness1.3 mm1.5 mm
DA-S
Thick fleece for rough substrates. Existing roof layers may remain after assessment.
Waterproofing layer1.3 mm1.5 mm
Overall thickness2.5 mm2.7 mm
DA-K
Fleece backing for bonded roofs. Also suitable for mechanical fixing or laying under ballast.
Thickness1.3 mm1.5 mm
Product images partly edited with AI assistance
Compare sheets
Large-area sheets reduce on-site seam welding and detailing.
DA-P
Sheet for gravel or green roofs. Laid loose in one piece.
Thickness1.2 mm1.3 mm1.5 mm2.0 mm
DA-F Sheet
Made-to-measure, also without ballast. Induction-fixed in a tested roof assembly.
Thickness1.3 mm1.5 mm
Product images partly edited with AI assistance